556H Honda/Acura Immobilizer Bypass Module After completing all remote start wiring connections, insert the Models Mode 1 Mode 2 vehicle key into the ignition switch. Do NOT turn the ignition on.
Headquartered in Southern California, DEI Holdings, Inc. Is the parent company of some of the most respected brands in the consumer electronics industry. DEI Holdings is the largest designer and marketer in North America of premium audio (sold under the Polk Audio®, Definitive Technology®, and BOOM® brand names), and consumer-branded vehicle.
Activate the remote start. ■ Honda Accord 2003-2004 ■ Honda Accord 1998-2002 ■ Honda CRV 2002-2004 ■ Honda CRV 1998-2001 ■ Honda Civic 2001-2004 ■ Honda Odyssey 1998-2003 ■ Honda Element 2003-2004 ■ Honda Pilot 2003 If the vehicle fails to start, check all ignition and tachometer con- ■ Acura RSX 2002-2004 ■ Acura CL 1998-2003 nections and retest. Do NOT proceed with 556H installation until ■ Acura TSX 2004 ■ Acura Integra 2000-2002 this test is successful. ■ Acura TL 2004 ■ Acura MDX 2001-2002 ■ Acura MDX 2003 ■ Acura TL 1998-2002 A successful test verifies that all ignition and tachometer con- ■ Acura 1.7EL 2001-2004 ■ Acura 1.6EL 1998-2000 nections are correct. This will eliminate the remote start as the Product Description If the vehicle remote starts, proceed with the 556H installation. Cause of a failure to start after completing the 556H installation.
The Honda/Acura Immobilizer anti-theft system uses a low-power Installation Instructions transponder mounted in the head of the ignition key. When the vehicle is started, the Key Cylinder Module converts the transponder signal and sends a secure, coded signal to the Engine Control 1. Remove steering column shroud to gain access to the wire harnesses at the rear of the ignition switch. Locate the appropriate wires exiting the ignition switch and Module. If the signal to the Engine Control Module is correct, the immobilizer receiver. The wire colors are listed in the Wire vehicle will start.
Wire the 556H as shown in the wiring diagram. The 556H uses a unique auto-program sequence to learn the secure Wire Color Guide code from the Key Cylinder Module and repeats it when remote start is activated, eliminating the need to leave a key in the vehicle.
GROUND BLACK (+) 12V BATTERY RED The 556H Honda/Acura Immobilizer Bypass Module integrates into IGNITION IN PINK the wiring for the Honda/Acura immobilizer anti-theft system to IGNITION OUT allow remote start capability, while still allowing normal function DATA YELLOW/BLACK of the factory immobilizer anti-theft system. DATA YELLOW N.C. ORANGE WARNING! It is recommended that the 556H Immobilizer Bypass Module only be installed by an authorized Directed dealer. Attempting installation without the proper tools and training can result in damage to the vehicle electronics. DATA 2 IN (-)GROUND IN REFERENCE ■ © 2005 Directed Electronics, Inc.
Vista, CA N556H 03-05 ORANGE/BLACK BLUE/WHITE GREEN Wire Connection Guide Pre-Installation Test IMPORTANT! Wire connections from the 555H to the Honda/Acura immobilizer wires should be done AFTER all remote start connections are completed and the following test is successful. PINK/BLACK BLACK: Connect this wire to a quality chassis ground (preferably scraped sheet metal) separate from other component ground locations. 1 ■ RED: Connect this wire to a constant (+)12 volt source.
Turn the ignition to the On position. ■ PINK: Connect this wire to the Ignition output from the ECM. Ensure that the module is in the correct mode by counting the ■ PINK/BLACK: Connect this wire to the Ignition input from the ■ ignition switch. Press the program button to switch between modes 1 and 2. YELLOW/BLACK: For mode 1 Connect this wire to data wire that 6. Once the mode is selected, turn the ignition Off. Connects from the ECM to the Ignition switch, for mode 2 7.
Turn the ignition back On and the LED will illuminate con- connect this wire to the Data wire from the Ignition switch. ■ LED flashes (i.e. 1 flash = mode 1). YELLOW: Connect this wire to the same data wire listed above for mode 1, for mode 2 connect this wire to the Data wire from the firming that the module has been programmed. Turn the Ignition Off, remove the key and initiate the remote start sequence.
![]()
■ ORANGE: Not Connected NOTE: You must use the BLACK master key to complete the pro- ■ ORANGE/BLACK: Not Connected for mode 1, for mode 2 this wire gramming procedure. Is connected to the Data 2 wire that connects the Ignition Troubleshooting switch and the ECM.
■ BLUE/WHITE: Connect this wire to the remote starter. ■ GREEN: Connect this wire to pin 1 at the ignition switch. With Ignition On 1.
LED flashing rapidly = module programmed, but not activated by input. Programming Instructions 2. LED On (constant) = module not programmed. Depress the programming button while inserting the wire With Remote Start 1. LED On (constant) = activated by remote start in mode 1. Harness into the connector. Release the programming button once the LED illuminates.
LED Off = activated by remote start in mode 2. Mode 1 Wiring Diagram HONDA ECM 7 PIN CONN. IGNITION BARREL 1 2 3 4 5 6 7 DATA PROGRAMMING BUTTON CUT IGNITION 556H GREEN REFERENCE BLUE/WHITE (-)GROUND IN ORANGE/BLACK N.C. YELLOW DATA YELLOW/BLACK DATA PINK/BLACK IGNITION OUT PINK IGNITION IN RED (+)12V BATTERY BLACK (-) GROUND REMOTE STARTER 2 © 2005 Directed Electronics, Inc.
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |